EmbeddedExpertIO
Need Help? Contact us at:
support@embeddedexpert.io
         Your free gift is on its way to your inbox, but before you go 
check out this very special offer, just for you!

Embedded Systems STM32 Low-Layer APIs(LL) Driver Development

STM32 Low-Level (LL) Drivers: ADC, UART, TIMERS, GPIO, SPI, I2C, RTC, WWDG, IWDG, RCC etc

25+ hours  | Complete source code included

Some Lesson Previews (2 of 72)

                                    Lesson : Coding : Configuring Systick
                                    Lesson : Coding : ADC Multichannel Driver with DMA (Part IV)
 30 Day Money Back Guarantee
  • ​Embedded Systems STM32 Low-Layer APIs(LL) Driver Development ($49.99 Value)
Total Value: $49.99
But today, you're getting all of this...
For Only $9.78
NOT UNDERSTANDING THE CODE


Sometimes I could get my firmware to work but I couldn’t understand a large portion of the code.

I didn’t know what some of the registers were doing. "Why do we write this hexadecimal number into that particular register ?" I would often ask.
CODE NOT WORKING - WASTED TIME

Other times I could understand every line of code in the firmware but couldn’t get the firmware to work.
CANNOT BUILD ANYTHING NEW -LACK OF CONFIDENCE, IMPOSTER

Because I wasn’t good enough, I couldn’t build exactly what I wanted if there were no already made drivers and libraries out there that I could use. Worst of all I couldn’t even get another microcontroller to work apart from the microcontroller used in class.
Long story short, I overcame all of this....
I devised a plan to master the fundamentals...
Quickly read the sections of interest in the datasheet...
Created my own firmware development checklist...
Created my own study guide...

I started creating courses to help other people like yourself master embedded systems development in the most efficient way possible, no waste of time, no frustrations. There is no need for you to go through the same roadblocks and frustrations I went through  some years ago.
The STM32 Low-Layer APIs ( as known as LL) offers a fast light-weight expert-oriented layer which is closer to the hardware than the HAL APIs (Hardware Abstraction Layer). The LL offers low-level APIs at the register level with better optimization. These require deep knowledge of the MCU and peripheral specifications which we shall cover in this course.

With a programming based approach, this course is designed to give you a solid foundation in firmware and peripheral driver development for the STM32 family of microcontrollers. The goal of this course is to teach you how to navigate the microcontrollers reference manual and datasheet to extract the right  information to professionally  build peripheral drivers and firmware using the STM32 Low-Layer APIs 

By the end of this course you will be able to develop drivers for peripherals like the ADC, UART,PWM, GPIO, TIMER,I2C, SPI, RTC, WWDG, IWDG, RCC, EXTI etc.  You will also master the STM32 architecture and how to build professional embedded firmware for STM32 microcontrollers.

Please take a look at the full course curriculum. 
I personally guarantee that by the end of this  course you will be able to accomplish the following
  • ​Master how to read Datasheets of Microcontrollers
  • Understand the Cortex-M Architecture
  • Write Analog-to-Digital Converter (ADC) drivers using Low-Level Functions
  • Write PWM drivers using Low-Level Functions
  • Write UART drivers using Low-Level Functions
  • Write TIMER drivers using Low-Level Functions
  • Write Interrupt drivers using Low-Level Functions
  • Write SPI drivers using Low-Level Functions
  • Write I2C drivers using Low-Level Functions
  • Write RTC drivers using Low-Level Functions
  • Write DMA drivers using Low-Level Functions
  • Write RCC drivers using Low-Level Functions
  • Write WWDG drivers using Low-Level Functions
  • Write IWDG drivers using Low-Level Functions
  • Introduction
  • ​Downloading the required documentation
  • ​Getting Started
  • ​Downloading CubeIDE
  • ​Installing Packages
  • ​Overview
  • Getting the right STM32 Package
  • ​General Purpose Input/Output Driver Development
  • ​​Overview of ARM Cortex-M General Purpose Input/Output Module
  • ​Coding : Developing a GPIO Output Driver
  • ​Coding : Developing a GPIO Input Driver
  • ​Universal Asynchronous-Synchronous Receiver-Transmitter (USART)
  • ​Overview of the UART Protocol
  • ​Coding : Developing a UART Transmitter
  • ​Coding : Developing a UART Receiver
  • Coding : Retargeting printf
  • ​General Purpose Timer Driver Development
  • ​Understanding the System Tick (SysTick) Timer
  • ​Coding : Configuring Systick
  • ​Understanding STM32 Timers
  • ​Coding : Creating timer delays
  • ​Coding : Timer output compare
  • ​Coding : Timer Input Capture
  • ​Analog-to-Digital Converters Driver Development
  • ​Understanding ADC Independents Modes
  • ​Coding : ADC basic driver
  • ​Coding : Transmitting ADC values through the UART
  • ​Real Time Clock (RTC) Programming
  • ​Understanding Real Time Clocks
  • ​Coding : Developing the RTC Alarm Driver Pt.1 - Configuring the RTC module
  • ​Coding : Developing the RTC Alarm Driver Pt.2 - Initializing the Alarm
  • ​Coding : Developing the RTC Alarm Driver Pt.3 - Displaying the time and dateCoding : Developing the RTC Alarm Driver Pt.4 - Testing the Alarm
  • ​Coding : Capturing Timestamp of events using the RTC
  • ​Coding :Exiting Standby mode using the RTC WakeUp Timer
  • ​Coding : Detecting System Intrusions using the RTC Tamper detector
  • ​Programming the Independent Watchdog (IWDG)
  • ​Overview of the Independent Watchdog
  • ​Coding : Developing the Independent Watchdog driver
  • ​Programming the Power (PWR) Module
  • ​Coding : Putting the system into Standby mode
  • Interrupt Programming
  • ​Understanding Interrupts
  • ​Coding : Input Interrupt Driver
  • ​Coding : ADC Interrupt Driver
  • ​Coding : UART Interrupt Driver
  • ​Direct Memory Access (DMA) Driver Development
  • ​Overview of the Direct Memory Access (DMA) Module
  • ​Coding : ADC Multichannel Driver with DMA (Part I)
  • ​Coding : ADC Multichannel Driver with DMA (Part II)
  • ​Coding : ADC Multichannel Driver with DMA (Part III)
  • ​Coding : ADC Multichannel Driver with DMA (Part IV)
  • ​Coding : ADC Injected Mode Driver (Part I)
  • ​Coding : ADC Injected Mode Driver (Part II)
  • ​Coding : ADC Analog WatchDog Mode Driver
  • ​Coding : UART DMA Case Study (Part I )
  • ​Coding : UART DMA Case Study (Part II)
  • ​Coding : UART DMA Case Study (Part III )
  • ​Coding : UART DMA Case Study (Part IV )
  • ​Inter- Integrated Circuit (I2C) Driver Development -TX
  • ​Understanding the I2C Protocol
  • ​Coding : Implementing the I2C Master Init Function
  • ​Coding : Implementing the I2C Slave Init Function
  • ​Coding : Implementing the I2C Callback Functions
  • ​Coding : Finalizing the application
  • ​Inter- Integrated Circuit (I2C) Driver Development -RxTx
  • ​Coding : Implementing the Init functions
  • ​Coding : Implementing the Callback Functions
  • ​Coding : Implementing the DMA Init Function
  • ​Coding : Implementing the Slave and Master Config Functions
  • ​Coding : Implementing the Interrupt Request Handlers
  • ​Coding : Finalizing the application
  • ​Serial Peripheral Interface (SPI) Driver Development
  • ​Understanding the SPI Protocol
  • ​Coding : Configuring the SPI Pins
  • ​Coding : Implementing the SPI Master Init functions
  • ​Coding : Implementing the SPI Slave Init functions
  • ​Coding : Implementing the SPI Callback functions
  • ​Coding : Finalizing the project
  • ​Programming the Window Watchdog (WWDG)
  • ​Overview of the Window Watchdog
  • ​Coding : Understanding the STM32 Clock Tree
  • ​Coding : Configuring the Window Watchdog to reset the MCU after a time window
My  courses have been reviewed by 1000+ students
Here are some of the reviews
  • ​​Embedded Systems STM32 Low-Layer APIs(LL) Driver Development ($49.99 Value)
Total Value: $49.99
But today, you're getting all of this...
For Only $15.99

Now it's time for you also to benefit from the...

Modern Embedded-C 
From Ground Up

 30 Day Money Back Guarantee

Remember, I have no doubt you will love the training but should in case you are not completely satisfied you can request a refund within 30 days of purchase and you shall be fully refunded with no questions asked.
Sounds fair ? 
I know there are some websites out there that offer you something cool for a low price, but then stick you into some program that charges your card every month.
This isn't one of them. There's NO hidden cost.

Thanks for taking the time to read this letter and I hope you enjoy the training!

-Israel N Gbati